Download “Scaling Health Mod 1.15.2/1.14.4 “, Most mods add content to the game to alter gameplay, change the creative feel.
This mod will, by default, allow the player to gain extra health. Mobs will also gain extra health, with the amount increasing gradually over time. Both player and mob health increases can be disabled. The rate at which the difficulty increases can also be changed.
- A per-player difficulty system. A difficulty value is tracked for each player, increasing slowly as time passes. As difficulty increases, mobs become stronger. For servers, mob strength is calculated based on one of several methods (see below). This feature can be tweaked/disabled.
- More player health! Or less. Players can obtain heart canisters that increase their maximum health. Normally, you keep the extra health even after dying (configurable). The player’s starting health can also be changed, and the max health cap is configurable as well.
- Lots of control. Plenty of config options to let you play the game however you like! There’s even an in-game config screen, so you can tweak options without restarting Minecraft.
Over time, the difficulty value that Scaling Health tracks for each player will increase. Currently, it takes around 60 real hours to reach maximum difficulty on default settings. The starting and maximum difficulty levels and the amount added each second are configurable. By default, idle players accumulate difficulty more slowly.
The difficulty value with determine how much extra health mobs can have. Mobs will also gain bonus attack damage. Higher difficulty values also increase the chance of mobs spawning as blights…
When mobs are spawned, an “area difficulty” value is calculated for the position the mob is spawned at. This value is then used to determine extra health/damage, chance of becoming a blight, etc. Depending on the mode, this is usually based on the difficulty level of all nearby players. “Nearby” means within the search radius, which is configurable.
- Weighted Average – A weighted average of the difficulty of all nearby players, with distance being used to calculate the weight. In layman’s terms, closer players have a greater impact on the area difficulty. This is the default mode.
- Average – Simply takes the average difficulty of all nearby players.
- Min Level – Takes the lowest difficulty level of nearby players.
- Max Level – Takes the highest difficulty level of nearby players.
- Distance from Spawn – Uses the distance from the world spawn to calculate the area difficulty. Basically, it’s distance multiplied by the “Distance Per Block” config option.
- Distance from Origin – Same as “Distance from Spawn”, but uses the distance from the origin (0, 0, 0).
- Distance and Time – A mix of Weighted Average and Distance from Spawn. Difficulty increases over time, but mobs also get stronger the further from spawn they are!
Mobs (both passive and hostile by default) will gain extra health as difficulty increases. The way extra health is added can be changed in the config file.
- Multiplier modes (MULTI, MULTI_HALF, and MULTI_QUARTER) – The mob’s health is multiplied, so that mobs with a higher base health will get a bigger boost. MULTI applies the same multiplier to all mobs, while MULTI_HALF and MULTI_QUARTER apply less for mobs with greater than 20 health. All of these should still apply more health than ADD mode. MULTI_HALF is the default.
- Additive mode (ADD) – A flat increase for all mobs. This is what Difficult Life used.
Blights are extremely powerful mobs. These are ordinary mobs (even from other mods) that have spawned with far more health, higher damage-dealing potential, and a variety of potion effects including a large speed boost. They also tend to spawn with armor. Blights have a purple fire effect at all times which makes them easy to identify, even if submerged in water.
By default, blights drop more heart containers than standard mobs (0-2 each by default, instead of a small chance of getting one) and ten times the XP. Blights have a variety of config options available, and can even be disabled entirely if that’s what you want.
A difficulty bar will appear on your HUD from time-to-time (there’s also a keybinding to show it). This bar actually has two parts, although you can’t tell in most cases. The upper part of the bar (the largest part) is the Area Difficulty at your location. You may see this portion grow when near other players on a server, or when using a distance-based mode. The lower part is your Player Difficulty. That’s the difficulty your player accumulates over time, which is used to calculate Area Difficulty in most cases.
Scaling Health includes a couple of commands. These are good for testing, goofing off, and working around bugs… If the player is not specified, the command uses the sender.
- /scalinghealth difficulty <amount> [player] – Sets the player’s difficulty to amount.
- /scalinghealth health <amount> [player] – Sets the player’s max health to amount.
How to install:
- Make sure you have already installed Minecraft Forge and Silent Lib.
- Locate the minecraft application folder.
- On windows open Run from the start menu, type %appdata% and click Run.
- On mac open finder, hold down ALT and click Go then Library in the top menu bar. Open the folder Application Support and look for Minecraft.
- Place the mod you have just downloaded (.jar file) into the Mods folder.
- When you launch Minecraft and click the mods button you should now see the mod is installed.
For Minecraft 1.12.2, 1.12.1, 1.12
For Minecraft 1.13.2
For Minecraft 1.14.4
For Minecraft 1.15.2